Milspec Paint
211 Gunther Ln.
Belle Chasse, LA 70037
Office: 504.393.9455
Fax: 504.433.1406
For more information or purchase request
Email: sales@milspecpaint.com
Legal/Privacy Info.
|
|
AQUAFLEX-510
WATERBORNE ACRYLIC BASED TOP COAT
Description:
Simco Aquaflex-510 is one component ready mixed finish paint based on water reducible modified acrylic emulsion and mixture of Rust inhibitive pigments.
The coating is designed to be used on properly prepared metal surfaces in new construction and maintenance where light to moderate chemical and high humidity exposure is a problem.
Principle Features:
|
Eliminates solvents odors, hazards and environmental problems. |
|
|
Good color and gloss retention. |
|
|
Easy application by airless and conventional spray. |
|
|
Protects cathodically steel substrate's. |
|
|
Forms a hard durable film with excellent resistance to mechanical damage. |
|
Conformance:
Conforms to the specification of Louisiana Department of Transportation and Development for waterborne bridge coating systems.
Technical Data
| Color and Finish: |
White & Gray; semi-gloss finish |
|
| Weight/Gallon, Pounds: |
Approx. 9.4 ± 0.1 |
|
| Viscosity KU: |
95 ± 5 |
|
| Sag Resistance, Min.: |
12 |
|
| Solids by Weight: |
Approx. 48% |
|
| Solids by Volume: |
Approx. 42% |
|
| Volatile Organic Compound (VOC): |
1.0 Lbs./Gal. (120 Grm/Ltr.) |
|
| Recommended DFT: |
3 mils (75 Microns) |
|
| Theoretical Spreading Rate: |
674 sq. ft./gal @1 Mil. DFT |
|
| Dry to Touch Max.: |
30 Minutes |
|
| Min. Interval Before Overcoating: |
1-2 Hours |
|
| Max. Interval Before Overcoating: |
No Limitation |
|
| Flash Point (TCC): |
None |
|
| Shelf Life: |
12 months |
|
| Storage: |
Store at 45ºF-85ºF |
|
Application Data:
| Manufacturer |
Gun Model |
Tip-Air Cap Combination |
|
| |
|
|
|
| DeVilbiss |
MBC or JGA |
704E |
|
| Binks |
#18 or #62 |
66PE |
|
Fluid hose should by 3/8" I.D. with a maximum length of 50 feet. Pot should always have dual regulation and be kept at same elevation as spray gun.
| Manufacturer |
Gun Model |
Pump |
|
| |
|
|
|
| Graco |
205-591 |
Bulldog |
|
| Binks |
Model 500 |
Mercury 5C |
|
| DeVilbiss |
#18 or #62 |
QFA-519 |
|
Hose should be 3/8" I.D. minimum, but ¼" I.D. whip end section may be used for ease of application. A maximum length of 100 feet is suggested. Best results are obtained using a .013" - .017" tip at 1200-2000 p.s.i.
Note: Nylon or Teflon type packing are available from pump manufacturer and are highly recommended.
| Thinning Requirements: |
Recommended Thinner: Fresh Water |
|
|
Airless Spray: None Required |
|
|
Conventional Spray: 10-15% |
|
|
Clean-up Thinner: Fresh Water |
|
Safety Precautions:
This product is offered for sale and use only to PROFESSIONALLY TRAINED INDUSTRIAL PERSONNEL. It is NOT FOR RESIDENTIAL USE. This product contains chemical ingredients and must be used with caution. Observe all health and safety precautions as listed on the Material Safety Data Sheet during storage, handling, application, drying and disposal. Do not attempt to use this product without consulting the current "Material Safety Data Sheet".
Non-Warranty:
The technical data listed herein has been compiled for your convenience and guidance, and is based upon our experience and knowledge. However, since we have no control over the use of this information of this product, no warranty expressed or implied, is intended or given. Simco Coatings, Inc. assumes no responsibility whatsoever for coverage, performance, or any other damages, including injuries resulting from use of this information or of products recommended herein.
|
 |
Copyright © 2004 MilspecPaint.com All rights reserved.
|
|
