Milspec Paint
211 Gunther Ln.
Belle Chasse, LA 70037
Office: 504.393.9455
Fax: 504.433.1406
For more information or purchase request
Email: sales@milspecpaint.com
Legal/Privacy Info.
|
|
SOLOKOTE-3160 H.B.
A UNI-C0AT HIGH BUILD PRIMER/FINISH
Generic Type:
Two-component modified Epoxy Polyamide.
General Properties:
Solokote-3160 is a high solids, rust inhibiting heavy bodied, high build epoxy primer/finish with excellent build characteristics, developed for use as a primer/finish one coat system or as a primer in a high build multi coat system depending upon performance requirements. The product contains optimum amounts of corrosion inhibiting pigments for prevention of rust undercutting. The unique formulation of the coating provides excellent water and crude oil resistance and can be applied over a tight rust surface in non-immersion conditions.
Recommended Uses:
Interior & Exterior of brine water, process & treating tanks, tank roofs, pipe racks, & structures subject to marine or chemical exposure where corrosion protection & appearance is desired.
Technical Data
| Color and Finish: |
Off white, red oxide, gray, aluminum, orange, eggshell finish |
|
| Application Temperature |
Normal |
Minimum |
Maximum |
|
| Ambient Air: |
60-90º F |
50º F |
120º F |
|
| Material: |
65-85º F |
55º F |
90º F |
|
| Surface: |
65-85º F |
50º F |
100º F |
|
| Humidity: |
20-80 % |
0 % |
85 % |
|
| Temperature Resistance |
|
|
| Continuous: |
110º F |
|
| Intermittent: |
140º F |
|
Percent Solids by Volume
(Part A&B Mixed): |
Approx. 84 ± 1% depending upon color |
|
| Theoretical Coverage: |
Approx. 1330 sq. ft. per gal. @ 1 mil. |
|
| Flash Point: |
84º F |
|
| Recommended DFT: |
10-16 mils |
|
| Wet: |
12-20 mils |
|
| Dry: |
10-16 mils |
|
| Drying Time: |
@ 50º F |
@ 70º F |
@ 90º F |
|
| Set to touch: |
12 hrs. |
6 hrs. |
3 hrs. |
|
| Recoat Time: |
48 hrs. |
24 hrs. |
12 hrs. |
|
| Non-Immersion: |
10 days |
2 days |
1 day |
|
| Immersion |
- |
5 days |
8 days |
|
| Shelf Life: |
12 months |
|
| Pot Life: |
3-4 hrs. @ 70º F |
|
| Mixing Ratio: |
4:1 by volume |
|
| Volatile Organic Compounds (VOC) |
1.1 lbs. / Gallon |
|
| Recommended Thinner: |
T-1 Thinner |
|
Surface Preparation:
Remove grease, dirt, oil and other foreign matter by suitable cleaning methods. SOLOKOTE-3160 may be applied over surfaces blasted to a "Near-White" metal according to SSPC-SP10 or to surfaces primed with approved shop primers. In many cases this product may also be applied over a hand or power tool prepared surface of tight rust.
Application Data:
| Conventional |
Fluid Tip |
Air Cap |
|
| |
|
|
|
| Devilbiss-MBC-510 |
D |
64 |
|
| Binks-Model 18 |
66 or 68 |
63 PB or 68 PB |
|
Airless:
Graco - 30 : 1 ratio with 206718 gun or speeflo commander 30 with H gun - .-019 or .031 orifice. The substrate temperature before coating should be 5º-7º F above the dew point.
Mixing:
Agitate Part A with jiffy mixer to reduce viscosity of material. Thoroughly mix component B for a few minutes. Below 65º F allow 30 minutes induction time before application. Apply in well atomized spray coat overlapping each pass 50%. May be thinned up to 1 pint per gallon with T-1 Thinner.
Safety Precautions:
(A) Use normal precautions such as gloves, facemasks.
(B) Adequate ventilation must be maintained.
(C) Explosion proof lights & electrical equipment.
(D) Non-Sparking shoes & tools for workers in area.
(E) This product contains flammable materials. Forbid all flames, smoking and welding in work area.
(F) Avoid breathing of vapor, contact with skin or eyes. If product comes in contact with skin or eyes, wash thoroughly with water and obtain medical attention.
Non-Warranty:
The technical data listed herein has been compiled for your convenience and guidance, and is based upon our experience and knowledge. However, since we have no control over the use of this information of this product, no warranty expressed or implied, is intended or given. Simco Coatings, Inc. assumes no responsibility whatsoever for coverage, performance, or any other damages, including injuries resulting from use of this information or of products recommended herein.
|
|
Copyright © 2004 MilspecPaint.com All rights reserved.
|
|
