Milspec Paint
211 Gunther Ln.
Belle Chasse, LA 70037
Office: 504.393.9455
Fax: 504.433.1406
For more information or purchase request
Email: sales@milspecpaint.com
Legal/Privacy Info.
|
|
TANKGUARD-2120
HIGH BUILD EPOXY MASTIC FINISH
Description:
A two pack high solid, low VOC; high build refined bleached tar epoxy coating. Used as a rust preventive coating for long-term protection to marine & industrial structures exposed to corrosive environments. Exhibits excellent resistance to impact, abrasion and chemical attack. It is compatible with a wide range of primers, but is also self-priming and can be applied to prepared steel or concrete surfaces.
Recommended Uses:
Can be used as tank coating in water and cargo/ballast tanks subject to water and/or petroleum immersion. Also recommended for interior and exterior of brine, water, process and treating tanks, etc. Pipe racks and structures subject to marine or chemical exposure where corrosion protection as well as appearance is desired.
Technical Data
| Generic Type: |
Non-tar epoxy polyamide |
|
| Color: |
Off-white, red oxide, gray |
|
| Flash Point: |
84º F |
|
| Shelf Life: |
One year (subject to re-inspection) |
|
| Finish: |
Semi-gloss |
|
| Mixing Ratio: |
4:1 base to hardener by volume |
|
| Pot Life @ 77º F |
3-4 hrs. |
|
| Volume Solids: |
84.0 ± 2% depending on color |
|
| Weight per Gallon: |
11.0 ± 0.2 |
|
| Recommended DFT: |
12-16 mils |
|
| Theoretical Coverage: |
At 12 mils. - 115 sq. ft./gallon |
|
| Drying Time @ 75º F: |
|
|
|
|
| To Touch: |
8 hours |
|
|
|
| To Topcoat: |
24 hours |
|
|
|
| To Full Cure: |
7 days |
|
|
|
| Volatile Organic Compounds (VOC): |
1.2 lbs./gallon |
|
Surface Preparation:
This product is designed to be applied on compatible and approved shop primers. Prior to the application of this product ensure that the painted substrate is intact and free from contaminates. All damaged areas of primer should be rectified and made good to ensure uniformity of system. The substrate should then be thoroughly degreased in accordance with SSPC-SPI. All dust should be removed from the substrate by using clean brushes and /or to the application of this product. For additional protection in severe corrosion environments additional coats of Simguard-2120 may be necessary for which another shade is recommended to provide a contrast in multi-coat application. On a primed surface a DFT of 325 microns 13 mils is recommended. When applied directly on a blasted and cleaned surface, a 400 micron 16 mil. DFT is advised. This product is self-priming and can be used on concrete.
Application Data:
Apply by airless spray.
Type and Percentage of Thinner: Airless spray: Thinner T-1 approx. 0-5% by vol.
Brush, roller: Thinner T-1 appro. 5-10 % by vol.
Details for airless spray: Output fluid pressure: 180 bar (atm) 2610 PSI
Minimum tip orifice: 0.018"
Potlife at 20º C/69º F: 3 hrs.
Cleaning Thinner: T-1
Additional Application Data:
At temperatures, below 15º C/59º F an induction time of the mixed components of 30 minutes should be allowed. The recommended method of application is by airless spray. Use of brush or roller should be restricted to small areas only. The substrate temperature before coating should be 5-7º F above the dew point. Application below 10º C/50º F or over 50º C/122º F and/or when the relative humidity is over 80% should be avoided. The spray fan should be adjusted to minimize overspray.
Safety Precautions:
During application take normal precautions such as wearing safety gloves, face masks an eye shields. Adequate ventilation must be maintained when applying this product in confined spaces. Observe all statutory local by-laws with respect to health and safety together with the laws governing storage of flammable liquid products. Keep material away from sparks or open flames.
Non-Warranty:
The technical data listed herein has been compiled for your convenience and guidance, and is based upon our experience and knowledge. However, since we have no control over the use of this information of this product, no warranty expressed or implied, is intended or given. Simco Coatings, Inc. assumes no responsibility whatsoever for coverage, performance, or any other damages, including injuries resulting from use of this information or of products recommended herein.
|
|
